Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in St. George?
Panel replacement in St. George typically costs $250 – $500 for a standard residential door, depending on how many sections are damaged and what the panel is made of. That range covers removing the bent or cracked section, matching the profile and color, and resetting the door so it travels and seals correctly. The written estimate sets the final price, and we give that estimate for free.
A single section on a common steel door usually lands at the low end. A wider section, a carriage-house style panel, or a door where the bottom section and the hardware underneath both took a hit lands higher. Most homes need one or two sections, not a whole new door, and knowing that before anyone knocks on your door is the whole point of a price guide like this.
Key Takeaways
- Typical panel replacement in St. George runs $250 – $500 per job, not per section.
- One bent bottom section is the most common reason homeowners call, and it’s usually a repair rather than a replacement.
- Panel matching matters more than most people expect; an exact profile and color match keeps the door looking original.
- Free estimates, and the written estimate is what you pay, not a ballpark over the phone that changes later.
- We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Panel Replacement Cost Breakdown (2026)
The table below shows what the individual pieces of a panel job usually cost in the St. George market. Most homeowners only need one or two lines from it, not all of them.
| Work item | Typical estimated range |
|---|---|
| Panel replacement (full job, common steel door) | $250 – $500 |
| Single lower section, standard profile | $250 – $350 |
| Wide or carriage-house style section | $300 – $450 |
| Multiple sections on the same door | $400 – $500 |
| Panel plus hardware affected by the impact | Toward the top of the range |
For comparison, the broader Rosemont Garage Door Service repair range across all jobs sits at $150 – $600, and a full new door installation runs $700 – $2200. That gap is why we push repair first. If a door has one bad section out of four, replacing the section almost always makes more sense than replacing the door.
What pushes a panel job up: an unusual color that has to be ordered and shipped, a panel with a window or decorative insert, damage that bent a track or hinge along with the panel, and a door old enough that the current panel profile no longer matches what’s hanging. What keeps it down: a standard section in a stock color, damage contained to the panel itself, and clear access to the door.
What Affects Panel Replacement Pricing in St. George
- Which section is damaged. The bottom section takes the most abuse because it’s the one the car, the mower and the desert grit reach first. Bottom sections are also the most commonly stocked, which usually keeps them at the lower end. A middle or top section on some doors means ordering the part.
- How the panel is made. Steel sections are the most straightforward to match and price. An aluminum or wood-look door, or one with a window insert, means more sourcing and a higher number inside the $250 – $500 range.
- Sun and heat exposure. St. George summers are hard on a west-facing door. Vinyl and painted finishes fade unevenly, so a new section can read a shade off from the faded ones around it. We talk through that before ordering so there are no surprises when the panel goes in.
- Damage that spread past the panel. A hard impact often bends a hinge, knocks a roller out of the track, or throws the door out of balance. Those are separate line items, and they matter for safety.
- Brand and profile match. We service Clopay, Amarr, Wayne Dalton, Raynor and other widely installed doors, and knowing a specific profile line makes a match far quicker than starting cold. A mismatched panel on an older door is where the quote starts climbing.
- Age of the surrounding door. A door that’s already flexing, with worn rollers and tired springs, may not be worth a panel. That’s a conversation about repair versus replacement, and we’d rather have it honestly than sell a panel into a door that’s near the end.
When a Panel Is Worth Replacing and When It Isn’t
Panel replacement makes sense when the door is structurally sound, the sections are the right profile, and the damage is contained to one or two pieces. It’s a repair that preserves the rest of a working door, and it’s the least expensive way to get a damaged door back to looking and functioning like it should.
Replacement starts to make more sense in three situations: the door has damage across most of its sections, the door is old enough that no current panel matches it and the mismatched look would bother you, or the surrounding hardware and springs are near the end anyway. We’d rather walk you through that call than have you spend $250 on a panel for a door that’s going to need a full install within the year.
What a Panel Replacement Visit Involves
A panel job is a hands-on repair, and understanding the process helps you know what you’re paying for. The technician starts by confirming the door is balanced and the tracks and hinges are true, because a new panel dropped into a bent track won’t stay straight. The old section is unbolted and removed, the replacement is fitted and aligned to the adjacent sections, and the door is cycled several times to check travel, seal and balance.
Spring tension and cable condition get checked while the technician is there. A panel with a snapped spring above it is a panel on a door that won’t open safely, and addressing both in one visit usually costs less than two separate calls. We don’t quote a number we haven’t seen the door for, and the written estimate spells out exactly what’s included.
Safety: What Not to Touch Yourself
Panel replacement often puts the technician near the torsion spring and cables, which are under serious tension. Springs and cables can cause severe injury if handled without the right tools and training, and we don’t recommend homeowners attempt that part of the work themselves. A panel that has come loose, a door off its track, or a spring that has snapped are all reasons to stop and call a trained professional rather than work around it.
If your door is hanging off a track or you hear a loud bang from the spring area, keep the door down and don’t operate it. Call and we’ll take it from there.
Panel Replacement vs. New Door in St. George
Panel replacement runs $250 – $500. A new door installation runs $700 – $2200. That overlap matters. On a common steel door in good shape, replacing the damaged section is clearly the better spend. On a door with widespread damage, a dated style you’ve been meaning to change, or a profile that no longer matches, the new door starts looking reasonable.
The deciding question isn’t price alone. It’s whether the door, once the panel is fixed, is going to keep working for years without the hardware and springs failing next. If the answer is yes, replace the panel. If the answer is murky, get an estimate for both and compare them side by side. Around St. George, doors take a lot of sun and a lot of cycle counts, so a door that’s already had multiple repairs is often closer to replacement than the owner thinks.
How to Save on Panel Replacement
- Get the estimate before authorizing work. Our estimates are free, and the written estimate is what you pay. There’s no reason to accept a price that isn’t in writing.
- Fix the panel before the damage spreads. A bent bottom section that rubs against the track can wear rollers and hinges over time. Catching it early keeps the job on the low end of the $250 – $500 range.
- Address related hardware in the same visit. A hinge or roller replaced in the same visit costs less than a second call for the same door.
- Match the panel rather than replacing more than you need. If one section is damaged and the rest are sound, replacing only that section keeps the number down.
- Ask about the color match up front. If sun fading means a new section will look different from the rest, a conversation now is cheaper than a surprise later.
Pricing is set per job by the written estimate, so there’s no formula we can shortcut. Call (866) 389-3687 for a free estimate and we’ll give you a straight answer about what your door needs. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why the Brand on Your Door Matters for a Panel Job
Panel replacement is a matching job as much as a repair job. The section has to fit the door’s profile, color and hardware pattern. We’re factory-familiar with LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor, which means the technician arrives knowing the quirks of your system rather than guessing from a photo. That’s less back and forth on ordering, and fewer callbacks because a panel was fitted into a track or hinge pattern that didn’t quite line up.
Garage doors are our only trade. Every hour of training and every part we work with goes into doors and openers, not into a broader home-service catalog. When a panel job turns out to involve an opener that’s not responding, that’s our territory too. We treat opener repair as its own discipline and isolate the actual problem, whether that’s the motor, the logic board, a remote or the safety sensors, rather than defaulting to a full replacement. One specialist handles repair, opener work and installation for the life of the door.
FAQs – Panel Replacement Cost
How much does garage door panel replacement cost in St. George?
Garage door panel replacement in St. George typically costs $250 – $500 for a standard residential door, with a single lower section usually landing at $250 – $350. Wider sections, window inserts, and jobs that include related hardware go toward the top of the range. Call (866) 389-3687 for an exact quote; estimates are free.
Is it cheaper to repair the panel or replace the whole door?
Repairing the panel is cheaper in the large majority of cases, at $250 – $500 versus $700 – $2200 for a new door installation. Replacing the whole door makes sense when damage covers most sections, when the door is old enough that no current panel matches it, or when the springs and hardware are near the end of their life anyway. Call (866) 389-3687 and we’ll tell you which side of that line your door is on.
Can you replace just one section of a garage door?
Yes, one section can usually be replaced on its own, and that’s the most common panel job we see. The section has to match the door’s profile and color, and the tracks and hinges have to be true so the new section travels straight. Typical cost for that single section is $250 – $350. Call (866) 389-3687 to get a quote on your specific door.
Why did my panel cost more than the typical range?
Panel jobs go above $500 when the door needs a non-stock color or profile, a window or decorative insert, or when the impact also bent a track, hinge or roller. Those are separate parts and separate labor. The written estimate itemizes every line so you can see exactly what pushed the number up. Call (866) 389-3687 for a free estimate on your door.
Can the panel be replaced the same day?
Often yes, if the section is in a stock color and profile and the hardware underneath is sound. Panels that need to be ordered take longer, and we’ll tell you the timeline before you commit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, so call (866) 389-3687 and we’ll get you on the schedule.
Do I need a permit to replace a garage door panel in St. George?
Replacing a panel on an existing door is generally treated as a repair rather than a structural change, but permit rules vary by jurisdiction. If you’re changing the door’s size, the opening, or the structural header above it, ask the city’s building department before the work starts. For panel-only work, we can talk through what’s involved when we give the estimate.
Book a Free Panel Replacement Estimate
If a bent or cracked section is the reason your door looks rough or doesn’t seal, the number is probably smaller than you fear. Call (866) 389-3687 for a free estimate. We’ll confirm what’s damaged, tell you whether a panel repair is the right call or whether the door is closer to replacement, and leave you with a written price before anything gets ordered. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 13 years of experience, we’re licensed and insured, and every estimate comes with upfront pricing and a satisfaction guarantee.
Pricing reflects the St. George market as of 2026. Rosemont Garage Door Service offers free estimates – call (866) 389-3687.
Written by the team at Rosemont Garage Door Service.
What Our Customers Say
"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Bryce Walsh"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Eric Hayes"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Mark Thompson